Description: The article below mainly contains the topic on netgear login. The content is about how to set up Netgear wireless N router. It is planned to help you to get your wireless roof which is supplied by permanent up and is used to run quickly and easily.
We have put together this tutorial to help you get your Wireless roof which is supplied by permanent up and is used to run quickly and easily, when you open your roofer, the black box itself is your wireless router, the yellow network cable will connect between your permanent modem and your wireless roofer.
You will need to fit a supplied adapter to the power supply to do, this simply insert the power, supply into the adapter, push down on copper contacts, close the adapter and tighten the screws with a screwdriver.
Next you need to remove a protective label that is covering the ports of your Wordle suitor, so to do this, simply peel off the label, let’s take a closer look at each port on your wireless router, you plug the power in here, this is the on and off button and you can connect up to four other computers using network cables, using these ports.
You plug the permanent modem into the yellow port, this is a hidden reset button and this is a security button for the purposes of this tutorial, it is best that you ignore the security button now at the back of your permanent modem.
This is the power cable, this is the network cable running to your computer and this is the cable which runs down from your outdoor equipment, plug out the network cable which is currently plugged into your permanent modem and plug in the yellow cable which was supplied with the wireless router, plug the other end of the yellow cable into the yellow port of your wireless router.
Next take the cable which plugs into your permanent modem and plug it into the port, next the yellow port on your wireless River plug in the power cable into the power socket on your router and plug the other end into the mains.
Turn on your wireless, refer using the switch at the back and your roof will begin, its startup sequence keeps an eye on the lights at the front of your wireless router, when the blue antenna life lights up, it means that your roofer is now transmitting a wireless signal, the eye light will flash when your roofer is waiting to receive an IP address from permanet.
When the eye light turns steady green, it means that I have received an IP address from permanet, when the power light turns green, it means that the startup sequence has completed and you are ready for the next.
At this point, the other end of the cable connected next to the yellow cable on your wireless router should already be connected to your computer, but if it is not, make sure that it is the one light on, your wireless router will flash intermittently, this indicates that information has been transferred between your computer and wireless router.
At this point, it is best to check that you have internet access, so open your browser and make sure you condole web pages.
Next you will need to configure your wireless router, so at the top of your browser, type in Rooter log and net, there is no need for WWE t cetera, simply type Rooter, log in net and press enter, you will then be presented with the logon screen for your wireless router, enter the username admin in lower case.
The password is password in lower case, then click on OK, if new firmware is available for your router, you will see this screen, if so, click on yes, it is always best that your hardware is running the latest firmware.
After you click yes, your loser will download the latest firmware from Netgear, this is an automated process and you have to wait for the completion, it can take a few minutes for the firmware to download.
After the firmware has downloaded, it will be installed to your wireless router, this is automated and you simply have to wait, when the installation of the firmware is completed, your roofer will restart and you will be presented with the login screen.
Once the log on screen reappears, enter the password with lowercase and click on OK, you are now ready to set up your word suitor for use with the permanent network from the menu on the left hand side.
Click on wireless settings, then choose a network name for your network, this can be any name you wish and this name will appear on your list of wireless networks later on for the purpose of this tutorial.
We have called our network your network name, select Europe from the pulldown menu on the region and set the channel to 4, click on WPA PSK and this will apply security to your roofer, choose a password by setting a password for your wireless router, it means that nobody else can access your network without your permission.
If you leave your network open, it means that anybody can log on and use your internet, once you have chosen the password, click apply, your roofer is now set up for the permanent network.
The next step is to determine which version of Windows you are running, the quickest way to determine the version windows you are running is to look at the bottom left of your screen.
If you see start and the windows logo, then you are running Windows XP, if you see a round circle similar as shown and the circle goes beyond the horizontal line of the taskbar, then you were running Windows Vista.
When you click the start button, you will see a menu similar to what you see now, if you’re running Windows 7, then you will notice that the start button is within the horizontal taskbar.
When you move the mouse over it, it shimmers, it can be easy to confuse Windows 7 and Windows Vista, however, if your computer is very new, then it will probably be running Windows 7, if you’re uncertain, it’s best that you consult the user manual that came with your computer.